แล้ว SSD แบบอื่นล่ะ ที่ไม่ใช่ Intel 910 เราจะเช็ค อุณหภูมิ หรือจำนวน Byte ที่เขียน และค่า อื่น ๆ เหมือนอย่างบน
Windows ได้หรือไม่
สามารถทำได้ครับ โดยติดตั้ง package smartmontools
#
apt-get install smartmontools เสร็จแล้วใช้คำสั่ง
#
smartctl -a /dev/sdbก็จะได้ผลออกมาเป็น
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.8.0-29-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen,
http://smartmontools.sourceforge.net=== START OF INFORMATION SECTION ===
Device Model: Samsung SSD 840 PRO Series
Serial Number: S1ATNSAF139872Y
LU WWN Device Id: 5 002538 5a019f483
Firmware Version: DXM05B0Q
User Capacity: 256,060,514,304 bytes [256 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4c
Local Time is: Mon Sep 15 20:50:30 2014 ICT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result:
PASSEDGeneral SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (53956) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 20) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 3765 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 362177 Wear_Leveling_Count 0x0013 094 094 000 Pre-fail Always - 207
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 066 055 000 Old_age Always - 34195 Hardware_ECC_Recovered 0x001a 200 200 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
235 Unknown_Attribute 0x0012 099 099 000 Old_age Always - 103
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 11262685629SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
เป็นต้น
ก็จะมีค่าต่าง ๆ แสดงผลออกมาเหมือนบน Windows
สามารถตรวจสอบค่า Total_LBAs_Written และค่าอื่น ๆ ได้
สำหรับ Samsung จากตัวอย่าง ค่า Total_LBAs_Written = 11262685629
สามารถคำนวณได้ เป็น 11,262,685,629 x 512 = 11G x 512 = 5.6TB
SSD Samsung ลูกนี้ มีการเขียนไปแล้วประมาณ 5.6TB เป็นต้น
ID # 241 Total LBAs Written
Represents the total size of all LBAs (Logical Block Address) required for all of the write requests sent to the SSD from the OS. To calculate the total size (in Bytes), multiply the raw value of this attribute by 512B. Alternatively, users may simply consult the Total Bytes Written indicator in Magician 4.0.
สำหรับของ Samsung อ้างอิงมาจากนี้
http://www.samsung.com/global/business/semiconductor/minisite/SSD/global/html/about/whitepaper07.html*** SSD แต่ละยี่ห้อ ผลอาจจะออกมาแตกต่างกัน ขึ้นอยู่กับผู้ผลิต ***
